Sand in Bellingham, MA

Looking for sand in Bellingham, MA? Ten Four Landscape Supply delivers sand across Bellingham from our yard at 26 Industrial Rd in Wrentham, and we also load pickups right at the yard. Bellingham sits at the western edge of our area, along Route 126 and Route 495. Even so, it is a regular stop, and Bellingham loads tend to be on the larger side.

Sand delivery in Bellingham, MA

The Charles River and Silver Lake run through town, and many homes sit on generous lots with room for big projects. Because many Bellingham lots are large, orders for loam, mulch and stone often come in several yards at a time.

Bellingham orders for base material often go toward pool surrounds, paver patios and long driveways. For that reason, sand is a regular order in Bellingham. In short, our Sand is clean sand for leveling, bedding, backfill and mixing, and it is sold by the cubic yard.

Why Bellingham customers choose our sand

Our sand is a clean, general-purpose sand sold by the yard. It spreads easily, levels well and compacts when wet. As a result, it handles most landscape and construction jobs around the home.

Sand is also easy to work by hand. For example, you can screed it flat with a board, tamp it with a hand tamper or wet it down to settle. That makes it a friendly material for DIY projects.

Popular uses for sand in Bellingham

Homeowners and contractors in Bellingham put sand to work in many ways. Here is where sand comes in handy:

• Leveling under pavers, patio stone and pools
• Bedding for pipes and utility lines
• Backfill around foundations and drains
• Filling low spots before loam and seed
• Mixing with loam to improve drainage
• Joint fill between stones (ask about polymeric products)

How much sand does a Bellingham project need?

First, measure the area in feet and multiply length by width. Then multiply by the depth in inches and divide by 324. The result is cubic yards, which is how we sell sand. Under pavers, sand is used as a thin, screeded bed of about 1 inch. For leveling or filling, however, depth depends on how low the area is.

For example, a typical Bellingham job of about 1,200 square feet needs roughly 3.5 yards at 1 inches, or 7.5 yards at 2 inches. Still, round up by half a yard for edges and settling. Or call (774) 372-1050, and we will check the math before the truck is loaded.

Delivery or pickup for Bellingham, MA

We deliver sand in Bellingham, MA by truck, placing the pile where you want it. Most Bellingham driveways handle our trucks well. Still, tell us about gates, pools or septic areas near the drop spot so the driver can avoid them.

1. Book the load. Call or send a quote request with the amount of sand and your Bellingham address.
2. Pick the drop spot. Next, choose firm, open ground close to the work area, clear of wires and branches.
3. Protect the surface. Then lay a tarp or plywood on pavement, so cleanup takes minutes.
4. Meet the truck. Finally, the driver calls ahead and places the pile as close to your spot as the ground safely allows.

Picking up at the yard

For Bellingham customers, the yard is a short highway drive east, so contractors often pick up between jobs. As a rule, a full-size pickup carries about about 1 yard of this material safely. So check your payload rating, and bring a tarp for the ride back to Bellingham.

When to order sand in Bellingham

Base work goes best when the ground is dry and firm. So late spring through fall is the prime season in Bellingham. In addition, plan driveway and patio projects before the first hard frost, because compaction is difficult on frozen ground.

How to screed sand for pavers

1. Compact the base. Build and compact a stone base first. Then check the slope with a level.
2. Set rails. Lay two pipes on the base as screed rails. Next, spread sand between them.
3. Strike it off. Pull a straight board across the rails. As a result, the sand bed is flat and even.
4. Lay the pavers. Place pavers on the sand without stepping on the screeded area.
5. Compact and sweep. Finally, compact the pavers and sweep fine material into the joints.

Sand in Bellingham, MA: FAQs

More for your Bellingham project

Sand usually works as part of a system. For instance, ¾″ bluestone forms a base, ⅜″ stone or sand sets the pavers, and loam finishes the edges. So if your Bellingham project needs more than one material, see ⅜″ Bluestone in Bellingham, ½″ Screened Loam in Bellingham and ¾″ Bluestone in Bellingham. As a result, one delivery can often cover the whole job.

We also deliver sand to nearby Franklin, Medway and Wrentham. For depth tips, coverage and product details, read the full Sand guide, or see every town we serve. For local background, Bellingham on Wikipedia is a good start.